AMPS™ (Auto-Regulated Mobile Power System™) generates 5-10 kVA of clean, mobile power from any combustion engine (i.e. vehicle, boat). The system seperates itself from traditional power generators by the quality of power being generated over a wide rotational input.

AMPS includes a custom alternator and a control management system. A custom alternator is installed to allow for full power load requirements, whether the engine is at idle, full throttle, or any variable in between. The control management system delivers the highest quality of regulated, clean, filtered power by utilizing multi-stage conversion technology and advanced isolation. When AC power is required, the system is easily activated.

Benefits:

• Power is mobile, versatile, and of a high quality
• Clean power to run sensitive electronic equipment
• No seperate fuel system or heavy trailer is required
• Small footprint
• Easily installed in both existing and new military vehicles
• Does not interrupt surrounding commmunication equipment

Applications:

• Remote operations
• Base stations
• Mobile aircraft ground support
• Mobile air traffic control
• Mobile communications
• Scene lighting
• Search and Rescue
• Recreational vehicles
• Construction sites
• Heating, cooling
• Emergency medical equipment

Features for AMPS Military & Marine and AMPS Mobile

Utilizing a patented high voltage alternator, combined with a quad-stage regulation and control loop, the AMPS provides a full load pure sine wave (60 Hz, 120 VAC / 60 Hz, 220 VAC / 400 Hz, 120 VAC) output with rotational input.   The input frequency can vary as much as 170 Hz to 1 kHz, while the output is regulated, or controlled, within 2% of specification.

• Clean power output over a wide range of input frequency and RPM
• Input/output isolation
• High efficiency
• Low heat dissipation
• AC input and AC output protection
• Over temperature
• Over voltage
• Under voltage
• Overload
• Soft start
• Output delay relay for power stabilization
• Enhanced EMI filtering
• Modular design
• Built for rugged applications
• Safety Features
• Short circuit protection
• Over temperature shutdown
• Input protection breaker
• Output protection breaker

Features for AMPS Mobile Only

• Top Displays (left to right)
• Amps
• Volts AC
• Watts
• Bottom Center Display
• RPM
• Temperature
• Frequency
• Illumination Strip
• Light bar
• 2 power outlets on unit

General
Output power capacity	5,000 VA / 10,000 VA (4,000 Watts / 8,000 Watts)
Output current (peak amp) 120 V	42 amps / 84 amps
Power Conditioning Topology
Nominal output voltage	120 Volts / 230 Volts / 120 Volts
Output frequency range (auto selected)	60 Hz / 50 Hz / 400 Hz
Output
Voltage Regulation and Frequency
Protection	Breaker
Output voltage regulation	± 2%
Wave form	Pure sine wave
Distortion	< 1%
Isolation
Common-mode noise rejection	Yes
Normal-mode noise rejection	Yes
High Frequency On-line Inverter
Overload capacity	> 110%
Crest factor	3:1
Transfer time	Zero
Efficiency	90% min
Physical
Weight (Military / Marine)	71.9 lbs / 32.61 kg
WxDxH (Miliary / Marine)	10 x 6.85 x 28.28 in (25.4 x 17.4 x 73.3 cm)
Weight (Mobile)	71.9 lbs / 32.61 kg
Weight (Mobile)	19 x 15 x 6.9 in (48.3 x 44.2 x 17.5 cm)
Environment
Temperature	-22º - 140º F (-30º - 60º C)
Storage temperature	-40º - 158º F (-40º - 70º C)
Humidity	10% - 95% non condensing
Shock	10 g for 11 mS, 1/2 sine
Display / Controls
Remote option	Yes
Load	10 Segment LED
Voltage	10 Segment LED
Temperature	Yes
Enable	Yes
Input
Input frequency	175 - 1k Hz
Protection	3Ø breaker
Input voltage	Alternator regulated
Alternator speed	1,750 - 10,000 RPM